CARBURETOR LEVER HEIGHT GAUGE FOR CARBURETOR INLET ADJUSTMENT
tlcarblever
$24.95
Tax included
GO KART INLET LEVER HEIGHT GAUGE By KARTECH
Inlet Lever Height Gauge For:
Walbro Carburetor
Tillotson Carburetor
Tryton Carburetor
and similar that have a metering lever arm
IAME KA100 REEDJET
IAME X30
IAME RL Leopard
Yamaha KT100S KT100SE Clubman
Yamaha KT100J
For setting the Inlet Lever Height On Carburetors
This Kartech gauge has different increments on it.
0.8 1.0 1.2 1.4
Most Professional engine builders use them.
To set the height of the metering lever arm, which bends over time,
Remove the top layers off the carburetor to expose the level arm section.
Measure the gap between the top of carburetor body, using the level gauge as a straight edge running across the top of the carburetor body, to the height of the end of the lever
You can move the gauge to see which height corresponds
To your lever height
With NO GASKET IN PLACE and measured below the top of the carburetor
KA100 is about 1.2mm
X30 is about 1.2mm
RL Leopard is about 1.2mm
PRD Fireball is about 1.4mm
SQ CHEETAH is about 1.4mm
The KTJ is about 1mm
The KTS is about 1mm 1.2mm
These are just BALL PARK setting and by experimenting slightly higher or lower will get your carby perfect.
YOU WILL ALSO NEED TO SET the BLOW OFF / POP OFF PRESSURE.. And we have that kit also available below
16 other products in the same category:
Wheel Weights Stick On 3 pack
$9.95
Tax included
GO KART FUEL TANK DROP KIT - Cap, Chaser, Breather,...
$19.95
Tax included
40mm Rear Axle Hub Spacers Coloured
$39.95
Tax included
Rotax Main Jet 150 Rotax Part No.: MJ150
Rotax Main Jet 150 Rotax Part No.: MJ150
$5.95
Tax included
Bead Locks Kartelli Corse thumb tightening set of 3
Set of 3 Kartelli Corse thumb bead locks easy to tighten, thumbtightening beadlocks. Suitable for Douglas, OTK, Kartelli Corse and most quality brand rims
$9.95
Tax included
Magnesium Rim Rear 210mm Kartelli Corse EACH
$86.95
Tax included
11 tooth sprocket suit Vortex Mini Rok
$70.95
Tax included
Rotax Power Valve Cover Clip Pre Evo Rotax Part No.:...
$14.95
Tax included
Number 6 Decal Large Black Carbon Fibre Style Sticker
Kart Number Decal Black Large Number 6 Suit nassa panel or number plate. Easy application of Carbon Fibre Style vinyl. KA approved font and size.
$5.95
Tax included
Kart Axle 50mm 1030mm OTK Compatible - 8mm 2 Peg...
$224.95
Tax included
Steering Boss Straight Flat - Black 19mm Shaft
Steering Boss Straight Flat - Black 65 mm long 19mm Shaft CNC Machined from 6000 series billet alloy
$34.95
Tax included
IAME X30 RL Leopard KA100 Air Box Socorem - Grey
$84.95
Tax included
Rotax Main Jet 155 Rotax Part No.: MJ155
Rotax Main Jet 155 Rotax Part No.: MJ155
$5.95
Tax included
STRIKE CLUTCH KT100J suit Yamaha J 12 Tooth
$349.95
Tax included
GO KART INLET LEVER HEIGHT GAUGE By KARTECH
Inlet Lever Height Gauge For:
Walbro Carburetor
Tillotson Carburetor
Tryton Carburetor
and similar that have a metering lever arm
IAME KA100 REEDJET
IAME X30
IAME RL Leopard
Yamaha KT100S KT100SE Clubman
Yamaha KT100J
For setting the Inlet Lever Height On Carburetors
This Kartech gauge has different increments on it.
0.8 1.0 1.2 1.4
Most Professional engine builders use them.
To set the height of the metering lever arm, which bends over time,
Remove the top layers off the carburetor to expose the level arm section.
Measure the gap between the top of carburetor body, using the level gauge as a straight edge running across the top of the carburetor body, to the height of the end of the lever
You can move the gauge to see which height corresponds
To your lever height
With NO GASKET IN PLACE and measured below the top of the carburetor
KA100 is about 1.2mm
X30 is about 1.2mm
RL Leopard is about 1.2mm
PRD Fireball is about 1.4mm
SQ CHEETAH is about 1.4mm
The KTJ is about 1mm
The KTS is about 1mm 1.2mm
These are just BALL PARK setting and by experimenting slightly higher or lower will get your carby perfect.
YOU WILL ALSO NEED TO SET the BLOW OFF / POP OFF PRESSURE.. And we have that kit also available below